Hi AdamM68,
Information about ppk2 can be found here. Schematics and manuals are included.
I got it and it is a very well designed and reliable unit.
I may be wrong about the absolute wrist tilt function not being usable.
I found a register that reroutes INT2 interrupts to the INT1 pad.
CTRL4_C (13h)
INT2_on_INT1 All interrupt signals available on INT1 pad enable. Default value: 0
(0: interrupt signals divided between INT1 and INT2 pads;
1: all interrupt signals in logic or on INT1 pad)
Here is a schematic from another STM accelerometer that roughly shows how it works:
Hi AdamM68,
You may be able to use an O-scope and some trickery but for what it does, NO. Being able to Source the Supply and vary it as well as the Amp meter mode to test actual battery drain. IMO one of nordics best tools, better than there dev boards (kitchen Sink) Easy to use and setup , being able to screen capture and real time display. It’s a tool and as others have indicated built and works VERY well Best $99 dollars I have spent to date. I have a DSS O-scope and it even beats that IMO,
HTH
GL 
1 Like
Hi Honvi,
Wow, Nice that would be great… NICE find. I’ll try to look into that , I’m using the Free-fall with Impact detection registers as well as motion detection along with double tap interrupts and it all works together well. I would really like to use the interrupts for all of it though. I’m currently at NAB 2023 so won’t know until I’m back this weekend.
cheers
HTH
GL
Just for all the noobs (like me) who are trying this code (since the documentation is low on this case). Note that the constants for the LEDs are named differently now (at least in my case). If you get errors that LEDR etc. can’t be found, they have to be renamed to LED_RED etc.
This is the code that worked for me.
/*****************************************************************************/
// IMU Interrupt Example for XIAO BLE Sense
// This example shows how to configure LMSD6S3TR-C on XIAO BLE SENSE to interrupt
// on INT1 after a "Double Tap" was recognized.
// Additionally, the device goes into System OFF state, after 5 interrupts were
// received. Another "Double Tap" will wake up the device again.
//
// by chuck
/*******************************************************************************/
#include "LSM6DS3.h"
#include "Wire.h"
LSM6DS3 myIMU(I2C_MODE, 0x6A);
#define int1Pin PIN_LSM6DS3TR_C_INT1
uint8_t interruptCount = 0; // Amount of received interrupts
uint8_t prevInterruptCount = 0; // Interrupt Counter from last loop
void setup() {
Serial.begin(9600);
pinMode(LED_RED, OUTPUT);
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_BLUE, OUTPUT);
setLedRGB(false, false, true); // set blue led
myIMU.settings.gyroEnabled = 0; // Gyro currently not used, disabled to save power
if (myIMU.begin() != 0) {
Serial.println("IMU error");
} else {
Serial.println("IMU OK!");
}
setupDoubleTapInterrupt();
pinMode(int1Pin, INPUT);
attachInterrupt(digitalPinToInterrupt(int1Pin), int1ISR, RISING);
}
void loop() {
setLedRGB(false, false, true); // reset led to blue only
Serial.print("\Iterrupt Counter: ");
Serial.println(interruptCount);
// if interrupt was received in this cycle
if (interruptCount > prevInterruptCount) {
Serial.println("\Interrupt received!");
setLedRGB(false, true, false); // set green only
}
prevInterruptCount = interruptCount;
if (interruptCount >= 5) {
// Trigger System OFF after 5 interrupts
goToPowerOff();
}
delay(500);
}
// -------------------- System ------------------------- //
void goToPowerOff() {
setLedRGB(false, false, false);
Serial.println("Going to System OFF");
setupDoubleTapInterrupt(); // not needed here, if already applied..
delay(100); // delay seems important to apply settings, before going to System OFF
//Ensure interrupt pin from IMU is set to wake up device
nrf_gpio_cfg_sense_input(digitalPinToInterrupt(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
// Trigger System OFF
NRF_POWER->SYSTEMOFF = 1;
}
// -------------------- Interrupts ------------------------- //
void setupDoubleTapInterrupt() {
uint8_t error = 0;
uint8_t dataToWrite = 0;
// Double Tap Config
myIMU.writeRegister(LSM6DS3_ACC_GYRO_CTRL1_XL, 0x60);
myIMU.writeRegister(LSM6DS3_ACC_GYRO_TAP_CFG1, 0x8E);// INTERRUPTS_ENABLE, SLOPE_FDS
myIMU.writeRegister(LSM6DS3_ACC_GYRO_TAP_THS_6D, 0x8C);
myIMU.writeRegister(LSM6DS3_ACC_GYRO_INT_DUR2, 0x7F);
myIMU.writeRegister(LSM6DS3_ACC_GYRO_WAKE_UP_THS, 0x80);
myIMU.writeRegister(LSM6DS3_ACC_GYRO_MD1_CFG, 0x08);
}
void int1ISR()
{
interruptCount++;
}
// -------------------- Utilities ------------------------- //
void setLedRGB(bool red, bool green, bool blue) {
if (!blue) { digitalWrite(LED_BLUE, HIGH); } else { digitalWrite(LED_BLUE, LOW); }
if (!green) { digitalWrite(LED_GREEN, HIGH); } else { digitalWrite(LED_GREEN, LOW); }
if (!red) { digitalWrite(LED_RED, HIGH); } else { digitalWrite(LED_RED, LOW); }
}
In any case, thanks a lot for the code. I was looking for a free-fall detection and couldn’t find any working code. I hope yours will help me develop something I need.
Hi there, This One is working.
HTH
GL
Hey @PJ_Glasso! I realize this post is many moons old by now, but I was wondering if you had any insight as to why your “double-tap to wake/sleep” code works for the mbed-enabled board version (Seeed NRF52 mbed-enabled Boards, v2.9.0) but not the non-mbed version (I’m using Seeed NRF52 Boards v1.1.8)?
For context, when running on the non-mbed board version, double-tapping increments the interrupt counter, and the board ostensibly enters a power-off state momentarily, only to re-awake immediately. (This is even when including the delay as suggested.) Any suggestions on where to start if I wanted to adapt your code to non-mbed?
It’s my understanding that Seeed themselves recommend the mbed-enabled board versions when doing more advanced work with the IMU, but I’ve also heard that this choice can lead to headaches down the road due to poorer documentation than the Adafruit board library.
Apologies also if I’m asking the wrong questions–it’s probably clear that I’m new to this stuff, haha. Thanks in advance!
Hi there,
Yep roll back the board support package , the 2.9.1 doesn’t work
If you follow the threads you’ll see more.
Always, when-ever a known demo that should work, doesn’t, it’s always the BSP , LOL
that breaks them.
I prefer the mbed , but the power savings is way better if you use non-mbed.
Seeed needs to circle this square.
HTH
GL PJ
1 Like
Any working code for deep sleep with Ble and is it possible A capacitive sensor act as a power button to turn on/off the device with a few seconds of hold. The device enter to sleep/deep sleep mode when idle and able to be woken up when the USB is plugged in, and a certain sequence of tapping on the capacitive sensor is completed.
Hi there,
There is. The Sleep demo with Tap to wake interrupt could be shoe-horned into that easy.
HTH
GL PJ
1 Like
/*/
// IMU Interrupt Example for XIAO BLE Sense
// This example shows how to configure LMSD6S3TR-C on XIAO BLE SENSE to interrupt
// on INT1 after a "Double Tap" was recognized.
// Additionally, the device goes into System OFF state, after 5 interrupts were
// received. Another "Double Tap" will wake up the device again.
//
// Original by chuck
//poatched and toasted by pjg
/*/
#include "LSM6DS3.h"
#include "Wire.h"
#include <U8x8lib.h>
LSM6DS3 myIMU(I2C_MODE, 0x6A); // IMU
#define int1Pin 2
U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* clock=/ PIN_WIRE_SCL, / data=/ PIN_WIRE_SDA, / reset=*/ U8X8_PIN_NONE);
// OLEDs without Reset of the Display
const int buttonPin = 1; // the number of the pushbutton pin
int buttonState = 0; // variable for reading the pushbutton status
int BuzzerPin = A3;
uint8_t interruptCount = 0; // Amount of received interrupts
uint8_t prevInterruptCount = 0; // Interrupt Counter from last loop
void setup() {
Serial.begin(9600);
delay(1000); //relax...
Serial.println("Processor came out of reset.\n");
u8x8.begin();
u8x8.setFlipMode(1); // set number from 1 to 3, the screen word will rotary 180
pinMode(LED_BUILTIN, OUTPUT);// initialize the LED pin as an output:
pinMode(buttonPin, INPUT_PULLUP);// initialize the pushbutton pin as an input:
pinMode(BuzzerPin, OUTPUT);
pinMode(LEDR, OUTPUT);
pinMode(LEDG, OUTPUT);
pinMode(LEDB, OUTPUT);
setLedRGB(false, false, true); // set blue led
myIMU.settings.gyroEnabled = 0; // Gyro currently not used, disabled to save power
if (myIMU.begin() != 0) {
Serial.println("IMU error");
} else {
Serial.println("IMU OK!");
}
setupDoubleTapInterrupt();
pinMode(int1Pin, INPUT);
attachInterrupt(digitalPinToInterrupt(int1Pin), int1ISR, RISING);
u8x8.setFont(u8x8_font_8x13B_1x2_r);
u8x8.clearDisplay();
u8x8.setCursor(0, 0);
u8x8.print("Tap Demo");
}
void loop() {
setLedRGB(false, false, true); // reset led to blue only
u8x8.setCursor(0, 3);
u8x8.print(interruptCount);
Serial.print("\Iterrupt Counter: ");
Serial.println(interruptCount);
// if interrupt was received in this cycle
if (interruptCount > prevInterruptCount) {
Serial.println("\Interrupt received!");
setLedRGB(false, true, false); // set green only
}
prevInterruptCount = interruptCount;
if (interruptCount >= 5) {
// Trigger System OFF after 5 interrupts
goToPowerOff();
}
delay(500);
}
// -------------------- System ------------------------- //
void goToPowerOff() {
setLedRGB(false, false, false);
Serial.println("Going to System OFF");
u8x8.clearDisplay();
u8x8.setCursor(0, 3);
u8x8.print("SLEEP");
setupDoubleTapInterrupt(); // not needed here, if already applied..
delay(1000); // delay seems important to apply settings, before going to System OFF
//Ensure interrupt pin from IMU is set to wake up device
nrf_gpio_cfg_sense_input(digitalPinToInterrupt(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
// Trigger System OFF
NRF_POWER->SYSTEMOFF = 1;
}
// -------------------- Interrupts ------------------------- //
void setupDoubleTapInterrupt() {
uint8_t error = 0;
uint8_t dataToWrite = 0;
// Double Tap Config
myIMU.writeRegister(LSM6DS3_ACC_GYRO_CTRL1_XL, 0x60); //* Acc = 416Hz (High-Performance mode)// Turn on the accelerometer
// ODR_XL = 416 Hz, FS_XL = 2g
myIMU.writeRegister(LSM6DS3_ACC_GYRO_TAP_CFG1, 0x8E);// INTERRUPTS_ENABLE, SLOPE_FDS// Enable interrupts and tap detection on X, Y, Z-axis
myIMU.writeRegister(LSM6DS3_ACC_GYRO_TAP_THS_6D, 0x85);// Set tap threshold 8C
myIMU.writeRegister(LSM6DS3_ACC_GYRO_INT_DUR2, 0x7F);// Set Duration, Quiet and Shock time windows 7F
myIMU.writeRegister(LSM6DS3_ACC_GYRO_WAKE_UP_THS, 0x80);// Single & double-tap enabled (SINGLE_DOUBLE_TAP = 1)
myIMU.writeRegister(LSM6DS3_ACC_GYRO_MD1_CFG, 0x08);// Double-tap interrupt driven to INT1 pin
}
void int1ISR()
{
interruptCount++;
;
}
// -------------------- Utilities ------------------------- //
void setLedRGB(bool red, bool green, bool blue) {
if (!blue) { digitalWrite(LEDB, HIGH); } else { digitalWrite(LEDB, LOW); }
if (!green) { digitalWrite(LEDG, HIGH); } else { digitalWrite(LEDG, LOW); }
if (!red) { digitalWrite(LEDR, HIGH); } else { digitalWrite(LEDR, LOW); }
}
This code working i tested with pin2. Is it posible to detect usb power?
Hi, PJ_Glasso
I am experiencing same problem as esmunus but I just want to stay on BSP nrf52 v1.1.8
NRF_POWER->SYSTEMOFF = 1;
#define NRF_POWER_S ((NRF_POWER_Type*) NRF_POWER_S_BASE)
Do you know what is the peripheralAddr in your BSP 2.9.1?
What I found for nrf52840 seems it needs to be 0x40000000UL
Hi there,
cores/nRF5/nordic/nrfx/mdk/nrf52840_peripherals.h
but I don’t think the issue is that , I believe if you use the GPIO number and the delay it will work with the 1.1.8 BSP.
HTH
GL PJ 
Hi,
Yeah, doesn’t look like there would be a register problem. I am not sure where did you mean to use GPIO number?
The following goes to system_off it stays off with intention to test the power off
void goToPowerOff() {
Serial.println("Going to System OFF");
//Ensure interrupt pin from IMU is set to wake up device
// nrf_gpio_cfg_sense_input(digitalPinToInterrupt(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
delay(200);
// Trigger System OFF
NRF_POWER->SYSTEMOFF = 1;
}
The following wakes up immediately
void goToPowerOff() {
Serial.println("Going to System OFF");
//Ensure interrupt pin from IMU is set to wake up device
nrf_gpio_cfg_sense_input(digitalPinToInterrupt(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
delay(200);
// Trigger System OFF
NRF_POWER->SYSTEMOFF = 1;
}
Thanks, RW
Hi there,
Yes, So I went back and found the one that works with 1.1.8 as well, it’s a single nudge/tap and could be adjusted to the same function as the original, but this one sleeps properly and shuts down the flash also. It stays asleep until you beat it up a little (low sensitivity)
You can blend these two together and get what you need.
HTH
GL PJ
// This is compiled with BSP 1.1.8 , sleeps AOK, and wakes up with a nudge via the Tap
// interrupt as GPIO
// toasted and poached by PJG 4/29/24
//
#include <Adafruit_SPIFlash.h>
#include <LSM6DS3.h>
#include <nrf52840.h>
#include <Wire.h>
Adafruit_FlashTransport_QSPI flashTransport;
LSM6DS3 myIMU; // Default is I2C mode
void QSPIF_sleep(void)
{
flashTransport.begin();
flashTransport.runCommand(0xB9);
flashTransport.end();
}
void setupWakeUpInterrupt()
{
// Start with LSM6DS3 in disabled to save power
myIMU.settings.gyroEnabled = 0;
myIMU.settings.accelEnabled = 0;
myIMU.begin();
// Set up the accelerometer for Wake-up interrupt.
// Per the application note, use a two step set up to avoid spurious interrupts
// Set up values are from the application note, and then adjusted for minimum power
myIMU.writeRegister(LSM6DS3_ACC_GYRO_WAKE_UP_DUR, 0x00); // No duration
myIMU.writeRegister(LSM6DS3_ACC_GYRO_WAKE_UP_THS, 0x02); // Set wake-up threshold
myIMU.writeRegister(LSM6DS3_ACC_GYRO_TAP_CFG1, 0x80); // Enable interrupts and apply slope filter; latch mode disabled
myIMU.writeRegister(LSM6DS3_ACC_GYRO_CTRL1_XL, 0x70); // Turn on the accelerometer
// ODR_XL = 833 Hz, FS_XL = ±2 g
delay(4); // Delay time per application note
myIMU.writeRegister(LSM6DS3_ACC_GYRO_CTRL1_XL, 0xB0); // ODR_XL = 1.6 Hz
myIMU.writeRegister(LSM6DS3_ACC_GYRO_CTRL6_G, 0x10); // High-performance operating mode disabled for accelerometer
myIMU.writeRegister(LSM6DS3_ACC_GYRO_MD1_CFG, 0x20); // Wake-up interrupt driven to INT1 pin
// Set up the sense mechanism to generate the DETECT signal to wake from system_off
// No need to attach a handler, if just waking with the GPIO input.
pinMode(PIN_LSM6DS3TR_C_INT1, INPUT_PULLDOWN_SENSE);
return;
}
void setup()
{
pinMode(LED_RED, OUTPUT);
pinMode(LED_GREEN, OUTPUT);
digitalWrite(LED_RED, HIGH);
digitalWrite(LED_GREEN, HIGH);
QSPIF_sleep();
// Flash green to see power on, reset, and wake from system_off
digitalWrite(LED_GREEN, LOW);
delay(1000);
digitalWrite(LED_GREEN, HIGH);;
// Minimizes power when bluetooth is used
NRF_POWER->DCDCEN = 1;
}
void loop()
{
// FreeRTOS will automatically put the system in system_on sleep mode here
delay(10000); // Measure idle loop power during this period
// Flash red before system_off sleep
digitalWrite(LED_RED, LOW);
delay(1000);
digitalWrite(LED_RED, HIGH);;
// Setup up double tap interrupt to wake back up
setupWakeUpInterrupt();
// Execution should not go beyond this
NRF_POWER->SYSTEMOFF=1;
}
The Led will turn green when it wakes up ! 
Hi,
Try to use digitalPinToPinName instead of digitalPinToInterrupt when calling nrf_gpio_cfg_sense_input, which will expect a nrf_gpio pin input (should be P0.11). However, digitalPinToInterrupt will only return the Arduino pin number, they are not matched. digitalPinToPinName(P) will do the pin mapping, g_ADigitalPinMap[P] will also work, actually which is the definition of digitalPinToPinName.
nrf_gpio_cfg_sense_input(digitalPinToPinName(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
Hi,
Thanks!
That was a solution for me.
nrf_gpio_cfg_sense_input(digitalPinToPinName(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
part of setup
// Attach interrupt signal from myIMU for wake up function
pinMode(int1Pin, INPUT_PULLDOWN);
// Attach interrupt to the IMU
attachInterrupt(digitalPinToInterrupt(int1Pin), int1ISR, RISING);
// Attach interrupt to the IMU for wakeups
nrf_gpio_cfg_sense_input(digitalPinToPinName(int1Pin), NRF_GPIO_PIN_PULLDOWN, NRF_GPIO_PIN_SENSE_HIGH);
setupDoubleTapInterrupt();
and my goToPoweOff
void goToPowerOff() {
Serial.println("Going to System OFF");
// Delay to allow serial to print
delay(500);
// Trigger System OFF
NRF_POWER->SYSTEMOFF = 1;
}
Hi,
Is it expected that when you trigger SYSTEM_OFF, the nrf52840 stays in its last state? I have turned on LED_RED ON before triggering SYSTEM_OFF, and it stays ON. Is this expected behavior?
Hi there,
It is, and will be reflected in the power draw asleep. You can shutdown the SD as well may override that behavior?
Some users also “flush” the serial port in order to avoid any spurious uart interrupts.
HTH
GL PJ