I got it working again after purchasing a USB programmer, just plugged in the programmer and the 328 and used the Arduino IDE to do the writing.
Everything is fine now, but for the future this needs much better attention.
I have successfully flashed the seeeduino 328 with avrdude and ubuntu 9.04, so it can be done.
Don’t know if this will help you or not.
Two things for me are very different from your approach:
- I used adafruit.com USBtinyISP as the programmer, so mine read: avrdude -c usbtiny (etc.)
- I used the avrdude v5.5 but copied the section for ATMEGA328 from the seeeduino avrdude.conf file to the avrdude v5.5 avrdude.conf file. I copied this in right before the ATTINY2313 section in the conf file.
My guess is avrdude doesn’t like the type definition.
i had this issue on my board, soldered on the headers for UART and jumpered them to the ISP side, followed the steps verbatim, and boom problem solved. thanks for the detailed and correct documentation on how to fix this
Guys, really sorry to bring such trouble to you, we are glad to know that have managed to fix it. Here is a video from Kimio on reburning the bootloader, thanks to KM Mun for referring.
This issue is a serious lesson for us to be remembered, allow me to stick this post to top. Thank you!
Link to said video
I received a Seeeduino 328 ordered 2 weeks ago and it has the problem, when will corrected units start shipping?
Hi guys,
We will send it immediately after you start send the fault one back to us.
And please contact me you have sent it/them back
albert.miao {at} seeedstudio.com
Thanks
Albert
That wasn’t the question; I meant: “When will new orders ship without the issue?”
We have fixed the issue.
Hi,
i got my Seeduino V328 board today ( I ordered on 09/11/30).
I got the same error. Uploading the first sketch worked fine, after that i got following error:
avrdude: stk500_getsync(): not in sync: resp=0x00
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x51
so i have no usb controller… can i send it back?
br
Patrick
I’m sorry, we think we have fix the bootloader problem On November 3rd.
But it has appeared again.
Please Try the new method to fix the problem.
First put the package to your disk:
D:\Program Files\FixSeeeduino_v328
And run the avrdude-GUI.exe
fixed as the pdf shows, page 2 is the avrdude-GUI method.
please read the fuse first, and tell us the fuse configure.
thank you very much
Albert
FixSeeeduino_v328.zip (232 KB)
It works now.
Thanks
I just received a new Seeeduino V328 to replace my faulty one.
When I connect the new Seeeduino (06/23/2009) to my laptop with USB-cable, it flashes the L a couple of times and then starts flashing wildly L and TX for some time and after that only L flashes very fast. And occasionally it goes back flashing L and TX very rapidly.
If I click Tools-menu from the Arduino 0017 UI, all the leds goes off and after about second L and TX starts flashing very rapidly for some time.
When I try to upload sketch (Blink). UI says Uploading to I/O Board and L and TX starts to flash. I have waited for a long time, but it won’t do anything.
UI settings
Board: Arduino Duemilanove
Port: COM5 (checked and is the right port)
Switches on Seeeduino: USB - 5V - A
Hi Kain,
I’m sorry, it taken bothering to you again.
Please select board in Arduino IDE : Arduino Duemilanove or Nano w/ ATmega328
select the corresponding COM port.
And upload the BLINK sketch.
Did you see the RST LED flash, after you click upload sketch button?
Albert
Yes, 3 or 4 short flashes. Could the problem be in my laptop? I have tried several different COM-ports (changed USB Serial Port from Device Manager) without success. I have Windows XP.
What is the initial program loaded in my Seeeduino, should it blink the TX and L lights? Is it sending something? The last one I got just blinked the L.
Tried with another laptop, no success.
We have burn a Arduino bootloader to it, and upload a test sketch.
Please try reburn the bootloader, the method is published in this page.
Thanks
Albert
i followed the method using the avrdude-GUI but i still get the error:
avrdude: stk500_getsync(): not in sync: resp=0x3f
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x3f
i tried the command line version as well and everything seemed okay, there were no errors or fails but when i tried to upload a sketch it gave the same not in sync error.
It seems a serious problem with your Seeeduino 328.
Would you please send it back to us to fix and find out the problem?
and we will send you a replacement.
As Chinese new year is very close to us, we will get 14 days vacation soon(Feb.7~Feb.21), please send it after Feb.21.
Thanks
Albert
hey there!
I follow exactly the instructions to fix the Seeeduino board, also I did under windows,
something very bizarre happening, after burned the new bootloader, I could upload a first sketch from arduino IDE and it worked very very fine!! however , I couldn’t upload new sketchs, a communication problem arise…
So, looks like the original problem continue…
after a new bootloader burn, I uploaded a new sketch, but only one…
do you know how can I proceed now?
I’m Brazil, so it’s something impossible to send back …
the board…
Seeeduino
v328 06/23/2009
Hi,
Please reburn the fuse, then burn the bootloader.
sorry for late reply.
thanks
Albert