Search found 12 matches

by nw_giri
Fri Mar 29, 2013 7:14 pm
Forum: Shields
Topic: CAN-Shield
Replies: 8
Views: 3953

Re: CAN-Shield

hi,,

I can't find LOOPBACK and LISTENONLY MODE in Library ??

are u sure get library from WIKI site??
by nw_giri
Fri Mar 29, 2013 7:11 pm
Forum: Shields
Topic: Programming multiple NODE for CAN BUS SHEILD ?
Replies: 17
Views: 17755

Re: Programming multiple NODE for CAN BUS SHEILD ?

I will post my project using CAN bus ,,if it's done..

Once again thanks Loovee ..
:D
by nw_giri
Tue Mar 26, 2013 9:47 am
Forum: Shields
Topic: CAN-Bus Shield and Mega 2560?
Replies: 10
Views: 5719

Re: CAN-Bus Shield and Mega 2560?

Code: Select all

if still not running ,, Check X-tal.. 
sorry ,, I mean Crystal (X-tal),,
by nw_giri
Mon Mar 25, 2013 4:56 pm
Forum: Shields
Topic: CAN-Shield
Replies: 8
Views: 3953

Re: CAN-Shield

Hi jpcurrie,,

Which library did you use ?

:roll:
by nw_giri
Sat Mar 23, 2013 9:16 pm
Forum: Shields
Topic: CAN-Bus Shield and Mega 2560?
Replies: 10
Views: 5719

Re: CAN-Bus Shield and Mega 2560?

all you need to do :

1. Check the Wiring and schematics,,
2. Check SPI pin.
3. Put in 120 ohm resistor in parallel at CANH and CANL.
4. if still not running ,, Check X-tal..

Good luck ,
Cheers ,

:D
by nw_giri
Sat Mar 23, 2013 8:15 pm
Forum: Shields
Topic: Programming multiple NODE for CAN BUS SHEILD ?
Replies: 17
Views: 17755

Re: Programming multiple NODE for CAN BUS SHEILD ?

Code: Select all

INT8U buf[8]= {0, 0, 0, 0, 0, 0, 0, 0};         // you should init it first
Could you explain to me why must be {0, 0, 0, 0, 0, 0, 0, 0} ?
by nw_giri
Sat Mar 23, 2013 8:08 pm
Forum: Shields
Topic: Programming multiple NODE for CAN BUS SHEILD ?
Replies: 17
Views: 17755

Re: Programming multiple NODE for CAN BUS SHEILD ?

Sorry for the late reply..

Cool ,, it's working ..thanks Loovee..
by nw_giri
Thu Mar 21, 2013 6:02 pm
Forum: Arduino & Seeeduino
Topic: Seeeduino ADK Main Board - problem with ADK mode connection
Replies: 1
Views: 1532

Re: Seeeduino ADK Main Board - problem with ADK mode connect

As far as I know not all devices working in ADK ( Even it's using jellybean ROM ) ;

:D
by nw_giri
Wed Mar 20, 2013 10:07 am
Forum: Shields
Topic: Programming multiple NODE for CAN BUS SHEILD ?
Replies: 17
Views: 17755

Re: Programming multiple NODE for CAN BUS SHEILD ?

still no luck... :( :(

init successfull but no data receive..
by nw_giri
Fri Mar 15, 2013 12:34 pm
Forum: Shields
Topic: Programming multiple NODE for CAN BUS SHEILD ?
Replies: 17
Views: 17755

Re: Programming multiple NODE for CAN BUS SHEILD ?

I try using Masking and reading output data using serial monitor in extended mode.. sorry ,, I edited the code,,but still no data output in serial monitor Please correct me if there are any mistakes CAN RX modul Enter setting mode success set rate success!! Enter Normal Mode Success!! Begin to set M...